![]() Power and current: 120V, 60Hz: 48W, 0.4A operating, 0.8A inrush.Instantly set any program to sound active.Trigger built-in static or automated programs (includes RGB fades).Includes footswitch, tripod with bag and transport case for lights.15-channel DMX-512 LED wash light system.With 108 red, green and blue LEDs per light, the 4BAR offers built-in automated and sound activated programs accessible with or without the foot switch. Each of the four low-profile lights can be positioned independently. This 15-channel DMX system includes a foot switch, adjustable tripod, packing bag and transport case. the packaging is great.The 4BAR is a pack-and-go must have for DJs, bands and other performers who want a complete LED wash light system. Go figure that out?.Īside from the syncing thing, these lights are great for my karaoke and stage hypnosis shows. if it does'nt, unplug from the wall again, wait a few seconds and plug it in again.įor some reason, the lights need to see each other as you power both up at the same time. plug it in again and look at both lights as power goes to them. if the slave light goes on and stays on when you turn both on, unplug the power supply from its source (this is the cord that plugs into wall). hook up the dmx line and power both up! (must be on the same power supply) (you'll know why in a bit). so here it is - set master to Snd and set the Slave to DMX (b001). After playing with the menu button and the up and down button, I know how to get between DMX, Auto and Snd. Hey guys, I had one heck of a time trying to figure out the settings to run my new lights together. Katherine & anybody else with troubles setting slave and master slave settings I think there might be an opportunity for me in this someway.Īnyway, I am very glad I made the investment in the 4-Bars, I think they are very good value for money, and this was certainly reinforced by my experience at the shoot this week. Ten very large old scanners used as fixed white spotlights, along with some pars. You would need a real lot of par cans to do what a couple of 4-Bars can do.Īlso interesting that no one at the club knew how to work the lighting other that to turn some static lights on. I was doing some video shooting at a fairly large club this week, about 700 capacity, and they had a boatload of old school (incandescent) lighting set up (about 10 Kilowatts total) and while it was cool to see that much all in one place the real advantages of the LED lighting became incredibly clear in a few minutes. They are bright enough on a small bar stage situation but you will need more than just a couple of these to do anything larger. Nearly drove me crazy figuring this out.īut I don't believe there is any way to reverse the left to right built in shows. ![]() I have 2 4-Bars and have found that the menus act differently if the fixtures detect DMX is present, which of course is not mentioned in the manual. S*** You can choose the desired speed of the internal programs. To switch to sound controlled mode, press the or Obviously, we are newbies, but it would help Chauvet if they would be REAL explicit in their manuals on this part.Ī*** You can choose the desired DMX address via the or buttons We have good DMX cable because Bill who frequents this forum sold it to us. We have tried both on Auto, we have tried both on sound, we have tried both on A 512, S 51. ![]() ![]() Now, we don't know what that was and the manual isn't explicit enough for newbies to try and figure out. I assume we were just lucky when we first set them up at home that both bars had the same programming in the menu that was needed. Got them to a gig Thursday night, and we can't get them to work in master/slave at all since then using the foot switch. OK, just got the 4 Bar, set them up at home, and they worked just fine in the master/slave mode. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |